51ºÚÁÏ

AQA GCSE Design and Technology (DT) - Exam Theory - Section 3.2 - Forces and Stresses This resource contains all of the key knowledge that the students are required to know for Section 3.2 - Forces and Stresses Forces and Stresses Tension Compression Shear Bending Torsion Reinforcing and Stiffening Lamination Webbing Folding The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Designing and Making - Product Analysis This resource contains all of the key knowledge that the students are required to know for Designing and Making - Product Analysis Product Analysis Analysis Categories Material Impact Analysis Analysis of Processes Social Impact Fair Trade The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students clarity and confidence in preparation for both the NEA and the written exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with the tracker (available for free) designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity, *(particularly effective when used with the tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enhanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on the tracker (available for free). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

A-Level Design and Technology (Product Design) Theory Section B (All 9 sections A through to I are also available) Section B - Advanced Materials Student Workbook This workbook comprehensively covers all content from section B of the theory, required for the A-Level DT exams. B1 - Biodegradable Materials B2 - Composites B3 - Smart Materials B4 - Modern Materials The workbook can be used as a framework for teaching, as well as for student independent working. Each sub-section includes worksheets and practice questions to aid retention and understanding of how the content may be presented in the exam. Progress can be tracked using the free tracker available from ACA Resources on TES. /teaching-resource/a-level-dt-theory-tracker-12396290 The content in this workbook has been designed to meet the demands of the AQA A-level in Design and Technology/ Product Design. The content also closely meets the requirements for Eduqas/WJEC, OCR and Edexcel.

A-Level Design and Technology (Product Design) Theory Section D (All 9 sections A through to I are also available) Section D - Industry Requirements and Standards Student Workbook This workbook comprehensively covers all content from section D of the theory, required for the A-Level DT exams. D1 - Modern Industrial and Commercial Practice D2 - Digital Design and Manufacture D3 - The Requirements for Product Design and Development D4 - Health and Safety D5 - Protecting Designs and Intellectual Property The workbook can be used as a framework for teaching, as well as for student independent working. Each sub-section includes worksheets and practice questions to aid retention and understanding of how the content may be presented in the exam. Progress can be tracked using the free tracker available from ACA Resources on TES. /teaching-resource/a-level-dt-theory-tracker-12396290 The content in this workbook has been designed to meet the demands of the AQA A-level in Design and Technology/ Product Design. The content also closely meets the requirements for Eduqas/WJEC, OCR and Edexcel.

A-Level Design and Technology (Product Design) Theory Section I (All 9 sections A through to I are also available) Section I - Wider Issues and Standards Student Workbook This workbook comprehensively covers all content from section I of the theory, required for the A-Level DT exams. I1 - Responsible Design I2 - Design for Manufacture and Project Management I3 - National and International Standards in Product Design The workbook can be used as a framework for teaching, as well as for student independent working. Each sub-section includes worksheets and practice questions to aid retention and understanding of how the content may be presented in the exam. Progress can be tracked using the free tracker available from ACA Resources on TES. /teaching-resource/a-level-dt-theory-tracker-12396290 The content in this workbook has been designed to meet the demands of the AQA A-level in Design and Technology/ Product Design. The content also closely meets the requirements for Eduqas/WJEC, OCR and Edexcel.

AQA GCSE Design and Technology (DT) - Exam Theory - Section 2.6 - Electronic Systems This resource contains all of the key knowledge that the students are required to know for Section 2.6 - Electronic Systems Electronic System Input, Process, Output Printed Circuit Board (PCB) Circuit Diagrams Resistor Voltage Switches - Toggle, Push, Slide Integrated Circuits Microcontrollers Programming Flowchart Symbols Timers Counters Logic Gates The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 1.2 - Production Systems - CADCAM This resource contains all of the key knowledge that the students are required to know for Section 1.2 - Production Systems - CADCAM CAD CAM CNC Subtraction of Material Addition of Material 2-Axis CAM 3-Axis CAM Global Communication The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 4.5 - Paper and Board Finishes This resource contains all of the key knowledge that the students are required to know for Section 4.5 - Paper and Board Finishes Finishes Advantages of Finishes Laminating Embossing Varnishing UV Varnishing Example Uses for Finish Types The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.4 - Shaping Materials (Hand Tools) This resource contains all of the key knowledge that the students are required to know for Section 5.4 - Shaping Materials (Hand Tools) Saws Rip Saw, Tenon Saw, Coping Saw, Hacksaw Chisels Plane File Abrasive Paper Drilling Bradawl Centre Punch Twist Bit Flat Bit Countersink Bit Hole Saw The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 1.5 - Products in Society This resource contains all of the key knowledge that the students are required to know for Section 1.5 - Products in Society Enterprise Crowdfunding Virtual Marketing Co-operatives Fairtrade Market Pull Technology Push Culture New Technology Design for Particular Groups The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 2.2 - Paper, Board and Timber This resource contains all of the key knowledge that the students are required to know for Section 2.2 - Paper, Board and Timber Paper Properties Cartridge Paper Layout Paper Tracing Paper Grid Paper Bleed-Proof Paper Board Types and Uses Solid White Board Ink Jet Corrugated Duplex Foam Core Foil Lined Hardwood Softwood Timber The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.6 - Shaping Techniques This resource contains all of the key knowledge that the students are required to know for Section 5.6 - Shaping Techniques Shaping Techniques Milling Machines Lathes 3D Printing Metal Press Casting Die Casting Bending Materials Plywood Forming Line Bender Strip Heater Annealing The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 4.2 - Standard Components This resource contains all of the key knowledge that the students are required to know for Section 4.2 - Standard Components Standard Components Examples and Uses Bindings Seals Tapes Adhesives The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.7 - Moulding and Joining This resource contains all of the key knowledge that the students are required to know for Section 5.7 - Moulding and Joining Vacuum Forming Blow Moulding Injection Moulding Extrusion Gluing Soldering Brazing Welding The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Designing and Making - Design Strategies This resource contains all of the key knowledge that the students are required to know for Designing and Making - Design Strategies Systems Approach User-Centred Design Iterative Design Collaboration Client Involvement User Involvement Expert Opinion Modelling The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students clarity and confidence in preparation for both the NEA and the written exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with the tracker (available for free) designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity, *(particularly effective when used with the tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enhanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on the tracker (available for free). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

Tracker to be used with the A-Level DT Theory Resources (Available on TES ACAResources). /teaching-resources/shop/ACAResources Simple input: 1 = Section Complete h = Section set for homework n = Section not complete or overdue blank = Section not yet set Includes visual percentage completion bars (auto-generated) to give teacher and students clarity and opportunity for individual target setting. Also includes auto-generated progress bars for display in lesson, and printing as evidence of progress over time. Encourages students to take ownership of their learning of the exam theory, and the visual progress scores provide motivation and clear goals. Students can work on different sections where appropriate, and in many cases students may wish to complete sections individually in their own time and bring them back to be ‘checked off’. Each A-Level DT Theory resource includes exam style questioning which can be used to further check understanding of each section upon completion.